CDA-4D-Front-Panel-with-Feet_1200x1059.webp
CDA-4D-Front-Angle-with-Rear-Ears_1200x673.webp
CDA-4D-Rear-Panel-with-Feet_600x336.webp
CDA-4D-Front-with-Rear-Ears_1200x673.webp

Bowers & Wilkins CDA-4D DSP Amplifier, 4 Channel 125 watts, Black (FP43648)

£1,850.00

Bowers & Wilkins CDA-4D DSP Amplifier, 4 Channel 125 watts, Black

The CDA-4D is a compact distribution amplifier, designed to power current and future Bowers & Wilkins Custom Installation loudspeakers. Embedded DSP allows optimisation of a wide range of products and dynamic EQ for Bowers & Wilkins subwoofers. It boasts four channels of 125 watts each, and its full-rack-width 1U design delivers high-performance from minimum rack space.

Impressively smart

To ensure the CDA-4D delivers in the modern custom installation system, it is equipped with Digital Signal Processing (DSP). This allows it to be used in wide variety of situations, provides control over IP and configuration, and for providing dynamic EQ for Bowers & Wilkins subwoofers.

Compact powerhouse

CDA-4D’s 1U size means that it takes up the minimum of rack real estate. But with four channels of 125 watts of Class D amplification on hand it can deliver power when required. Plus, as it’s bridgeable this can be configured to 2 x 250 watts, or a 2.1 setup (2 x 125 watts and 1 x 250 watts), where needed.

Flexible

Whether you are looking to upgrade an in-situ installation or planning a new one, the CDA-4D DSP amplifier is ideal. It can drive two zones, and works with a wide variety of Bowers & Wilkins products, both current and future

Bowers & Wilkins CDA-4D DSP Amplifier, 4 Channel 125 watts, Black

The CDA-4D is a compact distribution amplifier, designed to power current and future Bowers & Wilkins Custom Installation loudspeakers. Embedded DSP allows optimisation of a wide range of products and dynamic EQ for Bowers & Wilkins subwoofers. It boasts four channels of 125 watts each, and its full-rack-width 1U design delivers high-performance from minimum rack space.

Impressively smart

To ensure the CDA-4D delivers in the modern custom installation system, it is equipped with Digital Signal Processing (DSP). This allows it to be used in wide variety of situations, provides control over IP and configuration, and for providing dynamic EQ for Bowers & Wilkins subwoofers.

Compact powerhouse

CDA-4D’s 1U size means that it takes up the minimum of rack real estate. But with four channels of 125 watts of Class D amplification on hand it can deliver power when required. Plus, as it’s bridgeable this can be configured to 2 x 250 watts, or a 2.1 setup (2 x 125 watts and 1 x 250 watts), where needed.

Flexible

Whether you are looking to upgrade an in-situ installation or planning a new one, the CDA-4D DSP amplifier is ideal. It can drive two zones, and works with a wide variety of Bowers & Wilkins products, both current and future

Boasts four channels of 125 watts

  1. Full-rack-width 1U design

  2. Embedded DSP

  3. Class D amplification

  4. Audio SpecificationsLoad impedance range:>3Ω per channel (>6Ω in bridge mode)Output Power per channel, non-clipped:60W into 8Ω
    125 into 4ΩOutput Power bridge mode, non-clipped500W short term
    >125W continuousDC offset voltage:<50mVFrequency Response (-3dB):<10Hz to >30kHz, any load impedanceFrequency response accuracy, 20Hz-20kHz:+/-1dBDynamic range:>85dB A-WeightedTHD+N (1kHz, 500W, 4Ω):less than 1%Voltage Gain:15dB to 39dB, adjustableInput impedance:10kΩMaximum input voltage:4 VrmsSignal sense threshold:2.5mV (independent of Gain setting)Wake-up time:<0.2s (If other zones active)
    <2s (From all zones inactive)Turn-off time:15 minutes from last signal detected12V trigger input threshold:Typically 3V (recommended input is 5-15V) (TBC)Controls and IndicatorsFront panel:1 x Power LED (unit active – White, Fault – Red)
    1 x Network status LEDs (Signal present – White, Fault – Red)
    2 x Zone status LEDs (Signal present – White, Fault – Red)
    1 x Reset buttonConnectorsInput:2 x RCA (pair) Phono socket, Analogue line in
    2 x RCA Phono socket, Digital line in
    1 x EthernetOutput:2 x 5.08mm Pitch 4-way Phoenix Combicon style12V trigger control:1 x 3.5mm jack - 12V trigger IN
    1 x 3.5mm jack - 12V trigger OUT (Maximum 100mA pass-throughPowerPower consumption:<0.5W Standby, WoL disabled
    <2W Standby, WoL enabled
    300W maximum average (TBC)
    1,000W peak (TBC)AC supply:100-240V 50/60HzAC inlet:IEC C14, switchedThermalThermal dissipation:TBC BTU/hr (standby)
    TBC BTU/hr (Idle)
    TBC BTU/hr (max)DimensionsHeight:42.5mm (1.7in) 1U (57.5mm (2.3in) plus feetWidth:436mm (17.2in)Depth:300mm (11.8in)Net weight:4.0kg (8.8lb)Warranty InfoManufacturer's Warranty*:2 Year Return To BaseFaulty From New*:
    (Within 14 Days Of Purchase):Return to AWE for assessment.
    Please complete this online Returns FormAfter 14 Days Of Purchase*:
    (Within The Manufacturer's Warranty)Return to AWE for assessment.
    Please complete this online FormPost-Warranty Service and Repair:Please contact an authorised service centre: Sontec or Sound System Technology*Terms & Conditions:For further information regarding AWE's returns procedures please see chapters 7 & 8 in our Terms & Conditions